LAMPIRAN SERTIFIKAT AKREDITASI LABORATORIUM LK 001 IDN

Transkripsi

1 Temperatur 1 Termometer cairan dalam gelas 0 o C ~ 300 o C 0.73 o C 300 o C ~ 550 o C 0.9 o C 2 Sensor termokopel dengan indikator 0 o C ~ 400 o C 0.6 o C 400 o C ~ 1000 o C 1.5 o C 3 Indikator temperatur / resistansi -50 o C ~ 1760 o C 0.32 o C Indikator temperatur sensor termo 0 o C ~ 400 o C 0.6 o C kopel 400 o C ~ 1000 o C 1.5 o C 4 Termometer bimetal 0 o C ~ 500 o C 0.62 o C Temperature enclosure Oven, incubator, oilbath 25 o C ~ 400 o C 1.1 o C waterbath 25 o C ~ 100 o C 1.1 o C furnace 25 o C ~ 1000 o C 2.3 o C 5 Pyrometer (infra merah) 50 o C ~ 500 o C 3 o C 6 Thermohygrometer Temperatur 20 o C ~ 45 o C 0.63 o C relative humidity 30 %rh ~ 90 %rh 2 %rh Massa 7 Anak Timbangan g ~ 0.5 g 0.02 mg (Massa konvensional) 0.5 g ~ 1 g 0.03 mg 1 dari 17

2 2 g 0.04 mg 5 g 0.05 mg 10 g 0.06 mg 20 g 0.08 mg 50 g 0.09 mg 100 g 0.15 mg 200 g 0.3 mg 500 g 0.5 mg 1 kg 1 mg 2 kg 2 mg 5 kg 5 mg 8 Timbangan 0 g ~ 100 g 0.13 mg (elektronik) 100 g ~ 200 g 0.37 mg 200 g ~ 500 g 0.65 mg 500 g ~ 1000 g 1.3 mg 1 kg ~ 2 kg 3.7 mg 2 kg ~ 5 kg 11 mg 5 kg ~ 10 kg 10 mg 10 kg ~ 20 kg 0.85 g 20 kg ~ 50 kg 1.2 g 50 kg ~ 100 kg 2 g 2 dari 17

3 100 kg ~ 200 kg 4.3 g 200 kg ~ 400 kg 8.5 g 400 kg ~ 600 kg 11 g Volumetrik 9 Volumetric Glassware; 0 ml ~ 1 ml ml Volumetric Measures 1 ml ~ 2 ml ml 2 ml ~ 10 ml ml 10 ml ~ 25 ml 0.01 ml 25 ml ~ 50 ml 0.04 ml 50 ml ~ 100 ml 0.08 ml 100 ml ~ 250 ml 0.1 ml 250 ml ~ 500 ml 0.2 ml 500 ml ~ 1000 ml 0.3 ml 1000 ml ~ 2000 ml 0.5 ml Tekanan 10 Pressure test gauge 10 bar ~ 400 bar 0.1 % 1 bar = 10 5 Pa 11 Pressure gauge; 0 bar ~ 10 bar 0.02 bar 0 bar ~ 20 bar 0.07 bar 0 bar ~ 40 bar 0.08 bar 0 bar ~ 100 bar 0.2 bar 0 bar ~ 1000 bar 2 bar 3 dari 17

4 12 Pressure recorder 0 bar ~ 400 bar 1 bar 0 bar ~ 1000 bar 4 bar Gaya 13 Universal testing machine 0.01 tf ~ 1 tf 0.1 % 1 tf = 9806,65 N (tension) 1 tf ~ 2 tf 0.29 % 2 tf ~ 5 tf 0.27 % 5 tf ~ 10 tf 0.58 % 10 tf ~ 20 tf 0.29 % 20 tf ~ 50 tf 0.21 % 14 Universal Testing Machine 0.01 tf ~ 1 tf 0.1 % (compresion) 1 tf ~ 2 tf 0.3 % 2 tf ~ 5 tf 0.27 % 5 tf ~ 10 tf 0.58 % 10 tf ~ 20 tf 0.29 % 20 tf ~ 50 tf 0.21 % 50 tf ~ 100 tf 0.22 % 100 tf ~ 200 tf 0.23 % 15 Charpy impact testing machine 1 joule ~ 300 joule 0.3 % 16 Tensionmeter (push pull) 0 kgf ~ 50 kgf 0.03 % 50 kgf ~ 200 kgf 0.06 % 4 dari 17

5 17 Loadcell & hydraulic jack 10 kgf ~ 2000 kgf 0.5 % 2000 kgf ~ 5000 kgf 0.5 % 5000 kgf ~ kgf 0.58 % kgf ~ kgf 0.5 % kgf ~ kgf 0.5 % 18 Proving ring 10 kgf ~ 2000 kgf 0.5 % 2000 kgf ~ 5000 kgf 0.5 % 5000 kgf ~ kgf 0.58 % kgf ~ kgf 0.5 % kgf ~ kgf 0.5 % Torsi 19 Torque wrench 0.5 kgf.cm ~ 200 kgf.cm 0.3 kgf.cm 0 kgf.m ~ 100 kgf.m 0.12 kgf.m 20 Torque tester 0 kgf.m ~ 100 kgf.m 0.23 kgf.m Kekerasan 21 Durometer hardness tester type A,B,O 0 skala ~ 100 skala 0.24 skala type C, D, DO 0 skala ~ 100 skala 0.23 skala type OO 0 skala ~ 100 skala 0.68 skala 5 dari 17

6 22 Rockwell hardness tester type A 0 HRA ~ 100 HRA 0.13 HRA type B 0 HRB ~ 100 HRB 0.15 HRB type C 0 HRC ~ 100 HRC 0.32 HRC 23 Vickers hardness tester 0 HV ~ 1000 HV 1.5 HV 24 Microvickers hardness tester 0 µhv ~ 1000 µhv 1.2 µhv 25 Brinell hardness tester 10 HB ~ 3000 HB 0.41 % Panjang 26 Gauge block 0.5 mm ~ 10 mm 0.11 μm 10 mm ~ 25 mm 0.11 μm 25 mm ~ 50 mm 0.12 μm 50 mm ~ 75 mm 0.13 μm 75 mm ~ 100 mm 0.14 μm 100 mm ~ 150 mm 0.58 μm 150 mm ~ 200 mm 0.6 μm 200 mm ~ 250 mm 0.61 μm 250 mm ~ 300 mm 0.63 μm 300 mm ~ 400 mm 0.67 μm 400 mm ~ 500 mm 0.72 μm 27 Thread gauge (ulir luar) M 1 ~ M 80 4 μm 6 dari 17

7 28 Ring gauge 0 mm ~ 100 mm 0.9 μm 100 mm ~ 500 mm 2.2 μm 29 Setting bar (bar gauge) 0 mm ~ 100 mm 0.88 μm 100 mm ~ 500 mm 1.9 μm 30 Snap gauge 0 mm ~ 300 mm 1.4 μm 31 Standard scale 0 mm ~ 200 mm 0.82 μm 32 Reading scale/ Microscope microstructure 0 mm ~ 200 mm 0.82 μm 33 Dial indicator 0 mm ~ 10 mm 1.2 μm 0 mm ~ 25 mm 1.2 μm 0 mm ~ 50 mm 1.2 μm 34 Dial test indicator 0 mm ~ 5 mm 0.87 μm 35 Micro indicator 0 mm ~ 0.01 mm 0.29 μm 36 Cylinder gauge/ bore gauge 0 mm ~ 200 mm 1.8 μm 200 mm ~ 500 mm 2.6 μm 37 Outside micrometer 0 mm ~ 25 mm 0.8 μm 25 mm ~ 100 mm 1.2 μm 100 mm ~ 500 mm 1.7 μm 500 mm ~ 1000 mm 3 μm 7 dari 17

8 38 Inside micrometer 0 mm ~ 25 mm 1.2 μm 25 mm ~ 100 mm 1.4 μm 100 mm ~ 500 mm 2 μm 500 mm ~ 1000 mm 3.2 μm 1000 mm ~ 3000 mm 8.8 μm 39 Indicating micrometer 0 mm ~ 100 mm 1.4 μm 40 Micrometer head 0 mm ~ 25 mm 0.83 μm 25 mm ~ 100 mm 0.89 μm 41 Gear tooth micrometer 0 mm ~ 25 mm 1 μm 25 mm ~ 100 mm 1.1 μm 42 Gear tooth vernier 0 mm ~ 100 mm 12 μm 43 Depth micrometer 0 mm ~ 25 mm 1 μm 25 mm ~ 100 mm 1.1 μm 100 mm ~ 200 mm 1.2 μm 44 Depth vernier caliper 0 mm ~ 150 mm 12 μm 150 mm ~ 300 mm 15 μm 300 mm ~ 500 mm 17 μm 45 Vernier calliper 0 mm ~ 200 mm 20 μm 200 mm ~ 500 mm 25 μm 500 mm ~ 1000 mm 35 μm 1000 mm ~ 3000 mm 70 μm 8 dari 17

9 46 Height gauge 0 mm ~ 300 mm 20 μm 300 mm ~ 600 mm 30 μm 600 mm ~ 1000 mm 50 μm 47 Electric comparator interval scale : μm 0.6 μm interval scale : 1 10 μm 0.8 μm interval scale : μm 1.2 μm 48 Measuring microscope 200 mm x 200 mm 0.8 μm 49 Metal rules 0 mm ~ 1000 mm 0.28 mm 1000 mm ~ 2000 mm 0.5 μm 50 Carpenter square 500 mm x 500 mm 5 μm 51 Precision square 0 mm ~ 100 mm 2.1 μm 100 mm ~ 200 mm 2.2 μm 200 mm ~ 300 mm 2.3 μm 300 mm ~ 400 mm 2.4 μm 400 mm ~ 500 mm 2.7 μm 52 Steel tape measure 0 m ~ 50 m 0.3 mm 53 Textile tape measure 0 m ~ 200 m 0.63 mm 54 CMM & layout machine 0 mm ~ 300 mm 0.66 μm axis verification 0 mm ~ 600 mm 0.75 μm 0 mm ~ 1000 mm 0.94 μm 0 mm ~ 2000 mm 5 μm 9 dari 17

10 0 mm ~ 3000 mm 8 μm 0 mm ~ 4000 mm 10 μm 0 mm ~ 5000 mm 15 μm 0 mm ~ 6000 mm 20 μm 0 mm ~ 7000 mm 35 μm 0 mm ~ 8000 mm 50 μm 55 Position readout (linear scale) 0 m ~ 6 m 10 μm 56 Precision square level 0.01 mm/m ~ 0.1 mm/m 2.5 μm/m Precision level 0.01 mm ~ 1 mm 2.5 μm/m 57 Surface plate 0 mm ~ 2500 mm 2 μm 58 Steel straight edge 0 mm ~ 2500 mm 2 μm 59 Profile projector 500 mm x 500 mm 3.8 μm 60 Welding gauge 0 mm ~ 200 mm 13 μm 61 Bevel protactor 0 o ~ 180 o 1.4 (menit) 62 Busur baja 0 o ~ 180 o 27 (menit) 63 Sine bars 0 mm ~ 200 mm 1 μm 64 Angle gauge/ angle block 90 o Ultrasonic thickness gauge 0 mm ~ 200 mm 1.5 μm 66 Coating thickness gauge 0 mm ~ 2.5 mm 1 μm 67 Calibration foils 0 mm ~ 10 mm 0.81 μm 68 Calibration tester 0 mm ~ 5 mm 0.6 μm 10 dari 17

11 0 mm ~ 25 mm 0.7 μm 69 Checker/ step gauges 0 mm ~ 300 mm 0.65 μm 300 mm ~ 600 mm 1 μm 70 Height master 0 mm ~ 300 mm 0.61 μm 300 mm ~ 600 mm 1 μm 71 Pin gauge 0 mm ~ 10 mm 0.59 μm 72 Standard block UI 0 mm ~ 200 mm 2.4 μm 73 Step wedge 0 mm ~ 15 mm 2.1 μm 74 Mesh/ ayakan pasir W = 5 mm, d = 1 mm 2.6 μm 75 Motion stage (NC & CNC)/ linear measurement 0 m ~ 8 m 7.2 μm 76 Inside dial caliper 0 mm ~ 100 mm 26 μm 77 Holtest/ three point inside micrometer 0 mm ~ 175 mm 1.8 μm 78 Radius gauge 0 mm ~ 25 mm 2.8 μm Kelistrikan 79 Multimeter AC Volt (f = 50 Hz~1kHz) 1 mv ~ 330 mv 0.59 mv 330 mv ~ 3.3 V 5.9 mv 3.3 V ~ 33 V 14 mv 33 V ~ 330 V 75 mv 11 dari 17

12 330 V ~ 1000 V 0.6 V DC Volt 1 mv ~ 330 mv 33 μv 330 mv ~ 3.3 V 0.2 mv 3.3 V ~ 33 V 5.8 mv 33 V ~ 330 V 58 mv 330 V ~ 1000 V 0.58 V 80 AC current (f = 50 Hz ~ 1 khz) 29 μa ~ 3.3 ma 2 μa 3.3 ma ~ 33 ma 58 μa 33 ma ~ 330 ma 0.62 ma 330 ma ~ 3.3 A 6.9 ma 3.3 A ~ 11 A 59 ma DC current 81 0 ma ~ 3.3 ma 0.64 μa 3.3 ma ~ 33 ma 6 μa 33 ma ~ 330 ma 72 μa 0.33 ma ~ 2.2 ma 5.9 ma 2.2 A ~ 11 A 58 ma 82 Tahanan (Ohm) 0 Ω ~ Ω 6 mω Ω ~ Ω 19 mω Ω ~ kω 92 mω kω ~ kω 1 Ω 12 dari 17

13 kω ~ kω 10 Ω kω ~ MΩ 100 Ω MΩ ~ MΩ 5.8 kω MΩ ~ MΩ 60 kω 83 Oscilloscope Volt/Div (Vertical Deflection) 1 mv/div ~ 100 V/Div 0.59 mv time/div (horizontal deflection) 5 ns/div ~ 100 ms/div 0.58 µs 84 Clampmeter (Tang ampere) AC current (f = 50 Hz ~ 1 khz) 11 A ~ 550 A 16 ma/a DC current 11 A ~ 550 A 16 ma/a 85 Resistance box/ Standard 0 Ω ~ 2 Ω 0.03 mω (Source) 2 Ω ~ 20 Ω 0.2 mω 20 Ω ~ 200 Ω 1.6 mω 200 Ω ~ 2 kω Ω 2 kω ~ 20 kω 0.16 Ω 20 kω ~ 200 kω 1.6 Ω 200 kω ~ 2 MΩ 18 Ω 2 MΩ ~ 20 MΩ 0.4 kω 20 MΩ ~ 200 MΩ 22 kω 200 MΩ ~ 2 GΩ 2.1 MΩ 13 dari 17

14 Voltage (V) : 240 Volt, 86 Powermeter AC I = 3,3 ma; 33 ma; 330 ma; 3.3 ma, 11 A 7.3 mw/w Cos phi = 0.96 f = 50 Hz ~ 1 khz 87 Powermeter DC 7.3 mv/v voltage (V) = 240 Volt I = 3,3 ma; 33 ma; 330 ma; 3.3 ma, 11 A 88 Capacitance 0.33 nf ~ nf 0.66 pf f = 1 khz 0.5 nf ~ nf 0.71 pf 3.3 nf ~ nf 6.6 pf 11 nf ~ nf 9.8 pf 33 nf ~ nf 62 pf 110 nf ~ nf 90 nf f = 100 Hz 0.3 µf ~ µf 0.62 nf 1.1 µf ~ µf 0.98 nf 3.3 µf ~ µf 6.2 nf 11 µf ~ µf 9.8 nf 33 µf ~ µf 62 nf 110 µf ~ µf 90 nf 89 AC Voltage source 1 mv ~ 200 mv 27 µv (power supply source) 200 mv ~ 2 V 0.2 mv f = 40 Hz ~ 100 Hz 2 V ~ 20 V 2 mv 20 V ~ 200 V 20 mv 200 V ~ 1000 V 0.14 V 14 dari 17

15 90 DC Voltage source 1 mv ~ 200 mv 1.1 µv (power supply source) 200 mv ~ 2 V mv 2 V ~ 20 V 0.19 mv 20 V ~ 200 V 3.5 mv 200 V ~ 1000 V 6 V 91 Electrical Arc Welding machine Volt AC (f = 50 Hz) 0 V ~ 42 V 0.59 V Volt DC 0 V ~ 42 V 0.59 V AC current (f = 50 Hz) 0 A ~ 53 A 1 A 54 A ~ 88 A 1 A 89 A ~ 126 A 2.1 A 127 A ~ 167 A 1.4 A 168 A ~ 200 A 1 A 201 A ~ 228 A 1 A 229 A ~ 272 A 2.1 A DC current 0 A ~ 65 A 1.1 A 66 A ~ 100 A 1 A 101 A ~ 147 A 1.1 A 148 A ~ 198 A 1.9 A 199 A ~ 248 A 1.1 A 249 A ~ 292 A 1.1 A 15 dari 17

16 293 A ~ 337 A 2.1 A 338 A ~ 384 A 1.1 A 385 A ~ 431 A 1 A 432 A ~ 458 A 1 A 459 A ~ 507 A 1.7 A 92 DC Current (source) 1 µa ~ 2000 µa 0.7 µa 2 ma ~ 20 ma 0.01 ma 20 ma ~ 200 ma 0.06 ma 200 ma ~ 2 A 0.6 ma 93 AC Current (source) 1 µa ~ 2000 µa 0.7 µa f = 50 Hz 2 ma ~ 20 ma 0.01 ma 20 ma ~ 200 ma 0.12 ma 200 ma ~ 2 A 6 ma Instrumen Analitik 94 ph meter 0 ph ~ 14 ph 0.02 ph 95 Emission spectrometer C: 2.85 % ~ 3.36 % C: 0.042% Si: 0.92 % ~ 1.65 % Si: 0.046% Mn: 0.13 % ~ 1.08 % Mn: 0.069% P: % ~ 0.78 % P: 0.028% S: % ~ % S: 0.019% Cr: % ~ 0.41 % Cr: % 16 dari 17

17 Mo: % Mo: 0.016% Ni: % ~ 1.77 % Ni: 0.017% Al: 0.01 % ~ % Al: 0.018% Cu:0.157 % ~ 0.92 % Cu: 0.044% Sn:0.024 % ~ 0.07 % Sn: 0.019% Ti:0.003 % ~ % Ti: 0.005% V:0.005 % ~ % V: 0.011% Mg:0 % ~ % Mg: 0.005% Catatan: Terbaik dinyatakan sebagai ketidakpastian yang diperluas pada tingkat kepercayaan 95 % dengan faktor cakupan k = 2, dan memperhitungkan kontribusi ketidakpastian dari penggunaan standar acuan laboratorium, ketidakpastian dari proses kalibrasi dan kondisi yang berpengaruh serta ketidakpastian dari peralatan terbaik yang dapat dikalibrasi oleh laboratorium Disahkan oleh Sekretaris Jenderal Komite Akreditasi Nasional 17 dari 17