ICE RIGGING / TRUSS REGULATION EVENT NAME & DATE HALL

Transkripsi

1 ICE RIGGING / TRUSS REGULATION EVENT NAME & DATE HALL VENDOR (PREFERRED) (NO / YES). VENDOR NAME: SUBMITTED DESIGN/DRAWING (NO / YES). DATE SUBMITTED: RIGGER POINT USED WEIGHT RIGGING/TRUSS ONLY: TOTAL: OVERVIEW GAMBARAN UMUM Applicable safety provisions must be observed Peraturan keselamatan yang berlaku harus in the assembly of the objects to be suspended. diperhatikan dalam perakitan objek yang akan Loads must always be connected to the cable digantung. Beban harus selalu terhubung dengan vertically using the specified rope locks. It is kabel secara vertikal menggunakan jenis tali prohibited to attach any loads subject to tertentu. Dilarang mengangkat beban yang dynamic/continuous motion. The following bergerak dinamis/terus-menerus. Berikut adalah information regarding allowable and informasi mengenai struktur yang diijinkan dan unallowable structures, lifting gear, suspension tidak diijinkan, alat pengangkatan, elemen elements, load suspension equipment and suspensi, peralatan suspensi beban dan konektor. connectors. STRUCTURAL CONSIDERATIONS PERTIMBANGAN STRUKTURAL The object to be suspended must be located Objek yang akan digantung harus berada dalam within the stand boundaries up to a maximum batas-batas stand dan digantung hingga stand height. Suspended objects may not be ketinggian maksimal. Benda yang akan digantung used to secure items exhibited on the floor of tidak dapat digunakan untuk mengamankan the stand or stand components. No oblique barang-barang yang dipamerkan atau komponen loads may be applied to the roof support stand. Beban miring tidak dapat diterapkan structure. Lighting fixtures, monitors, untuk struktur pendukung atap. Perlengkapan loudspeakers, etc. must additionally be secured tata cahaya, monitor, pengeras suara, dll harus by a second, independent safety line. Electrical diberi pengaman tambahan, tali pengaman tanpa power may be supplied to suspended objects hambatan. Pasokan daya listrik ke objek yang only from the stand connection. digantung hanya dari koneksi listrik stand tersebut. Figure 1: Allowed and Not Allowed suspended types.

2 2 TON RIGGING POINT LOCATION LOKASI The 2 Ton rigging points in the Exhibition Hall are located on 9 meters centres at structural nodes. Titik rigging 2 Ton di Exhibition Hall terletak di tengah simpul struktur setiap 9 meter. Figure 2 & 3: Green dots show typical Exhibition Hall 2 T Rigging Points 100 Kg RIGGING POINT LOCATION LOKASI The 100 Kg rigging points in the Exhibition Hall located on a 2.25m or 3m grid between the main 9m beam intersections. Titik rigging 100 Kg di Exhibition Hall terletak diantara 2.25m atau 3m setiap kisi diantara pertemuan titik beam 9m. Figure 4: Purple dots show 100 Kg matrix in a typical Exhibition Hall

3 BEAM TIANG ATAP The visible ridge and rafter beams to accommodate a maximum 1 Ton point load along any one point, or combination of points up to 1 Ton over a 9m section of structural beam between the structural node points. These will be used for attaching beam clamps to chain motors. Tiang atap dan kasau balok yang terlihat dapat menampung maksimal 1 Ton beban di sepanjang satu titik, atau kombinasi dari berbagai titik hingga 1 Ton sepanjang 9m balok struktural antara titik-titik simpul struktural. Digunakan untuk memasang klem motor rantai. LOAD BEBAN Figure 5: Blue lines show typical Exhibition Hall visible beams available for clamping. The loads may be realised from vertical to 45 from vertical (at derated loads). Further structural analysis is required to be confirmed. Beban harus diperhitungkan dari sudut vertikal hingga 45 dari sudut vertical tersebut (derated loads). Analisa struktur lebih lanjut diperlukan untuk persetujuan pemasangan. Figure 6: indication of how lateral loads will derate the load capacity of a rigging point

4 CONNECTION TYPES JENIS-JENIS SAMBUNGAN ACCESSORIES FOR SUSPENDED OBJECTS AKSESORIS UNTUK OBJEK YANG DIGANTUNG

5

6

7

8

9 SAFETY USER KESELAMATAN PENGGUNA Workers must dress up to safety standards and use PPE (Personal Protective Equipment) that supports, namely: - using helmets and shoes - full body harness when climbing - dresses are polite and neat - gloves if needed. Para pekerja harus berpakaian Para pekerja harus berpakaian memenuhi standar keselamatan dan menggunakan APD (Alat Perlindungan Diri) yang mendukung, yaitu : - menggunakan helm dan sepatu - full body harness ketika memanjat - pakaian yang sopan dan rapi - sarung tangan jika diperlukan.

10 All necessary documents (inspection booklets, inspection reports, etc.) must be brought along and presented on request! Thank you for your kind attention and cooperation. IDR 2,000,000,00 Fine for who doesn t obey with this regulation. I will comply with all applicable regulations. Terima kasih atas perhatian dan kerjasama Bapak/ Ibu. Denda sebesar Rp. 2,000,000,00 akan diberikan bagi siapapun yang melanggar. Saya akan mematuhi segala ketentuan yang berlaku. Tangerang, 2017 ( )