PERMANENT MAGNET MOVING COIL: (PMMC) The PMMC movement is also called as the D arsonval movement. The difference is the direct reading is provided by scale and pointer. WORKING: The PMMC works on the motor principle i.e. when the current carrying conductor is placed in the magnetic field of the permanent magnet, it behaves as the electromagnet with its own north & south poles which tends to move or out of the field. The deflection of the pointer is directly proportional to the amount of current passing through the coil as the pointer is connected to the coil. When the DC flows through the coil the magnetic field is produced in the coil reacts with the permanent magnet. The resultant force turns the coil
along with the pointer over the reference scale. The angular deflection of the pointer is proportional to the amount of current flowing through the coil. CONSTRUCTION: The PMMC mainly consists of the permanent magnet, moving coli, balancing and controlling springs, scale and pointer. PERMANENT MAGNET: The permanent magnet is placed in such a way that it can produce more magnetic fields between two points. The two types of permanent magnets can be used depending upon the angular deflection, 1. U-shaped or horse shoe magnet 2. Concentric magnet Concentric magnet is used when the angular deflection of more than 220 ₀ C to 360 ₀ is required. MOVING COIL: The moving coil is made up of thin silk covered copper wire or enameled wire. It is wounded on the non-metallic former and pivoted on the jewel bearings to provide the electromagnetic damping. BALANCING & CONTROL SPRINGS: When the coil is supported on the jewel bearings the controlling torque can be obtained by two phosphorous bronze hair springs. The springs serve the current in and out of the coil thus producing the controlling torque. POINTER & REFERENCE SCALE: The pointer is made up of light weight material and carried by spindle over gratitude. The pointer is twisted at the end to avoid the parallax error. The scale is provided with different measurements in terms of millimeter or centimeter. ADVANTAGES OF PMMC: 1. The scale of the PMMC is uniformly designed. 2. It consumes less power (25µv to 200µv) 3. It has high accuracy in Dc measurements. 4. The single instrument can be used to measure the different ranges of current and voltages by the addition of shunt and series resistor to the PMMC. DISADVANTAGES OF PMMC: 1. It is used for the measurement of DC only. 2. It is costlier than the other instruments. The three systems are necessary to operate satisfactorily, they are 1. Deflecting torque system 2. Damping torque system 3. Controlling torque system
DEFLECTING SYSTEM: The force which is applied to the pointer to deflect from its zero position is called the deflecting torque. These systems of an instrument convert the electrical energy into the mechanical energy. CONTROLLING TORQUE: When the deflecting force is applied to pointer it deflects and must stop to the measured value. In the absence of controlling torque the pointer shoots to the final value for any magnitude of current. DAMPING TORQUE: The pointer deflects when it is applied with the deflecting force and should come to rest at the steady position. The pointer comes back to its steady position when the deflecting force is balanced by the controlling torque. Thus the pointer oscillates and rest at the steady position, this force is known as damping force. PERMANENT MAGNET MOVING COIL : ( PMMC ) Gerakan PMMC juga disebut sebagai gerakan Arsonval D'. Perbedaannya adalah pembacaan langsung disediakan oleh skala dan pointer. KERJA : The PMMC bekerja pada prinsip yaitu motorik ketika pembawa arus konduktor ditempatkan dalam medan magnet dari magnet permanen, berperilaku sebagai elektromagnet dengan utara & selatan kutub sendiri yang cenderung bergerak atau keluar dari lapangan. Defleksi pointer berbanding lurus dengan jumlah arus yang melalui kumparan sebagai pointer terhubung ke koil. Ketika DC mengalir melalui kumparan medan magnet diproduksi di bereaksi coil dengan magnet permanen. Gaya resultan mengubah kumparan bersama dengan pointer atas skala referensi. Defleksi sudut dari pointer sebanding dengan jumlah arus yang mengalir melalui kumparan. KONSTRUKSI : The PMMC terutama terdiri dari magnet permanen, bergerak coli, menyeimbangkan dan mengendalikan mata air, skala dan pointer.
PERMANENT MAGNET : The magnet permanen ditempatkan sedemikian rupa sehingga dapat menghasilkan medan magnet yang lebih antara dua titik. Kedua jenis magnet permanen dapat digunakan tergantung pada defleksi sudut, 1. U - berbentuk sepatu kuda atau magnet 2. Magnet konsentris Magnet konsentris digunakan ketika defleksi sudut lebih dari 220 ₀ C 360 ₀ diperlukan. MOVING COIL : Kumparan bergerak terdiri dari sutra ditutupi kawat tembaga tipis atau enamel kawat. Hal ini terluka pada non-logam bekas dan berputar pada bantalan permata untuk memberikan redaman elektromagnetik. KESEIMBANGAN & PENGENDALIAN SPRINGS : Ketika kumparan didukung pada bantalan permata torsi pengendalian dapat diperoleh dengan dua fosfor springs rambut perunggu. Mata-mata melayani arus masuk dan keluar dari kumparan sehingga menghasilkan torsi mengendalikan. POINTER & REFERENSI SCALE : pointer ini terdiri dari bahan ringan dan dibawa oleh spindle atas rasa syukur. Pointer ini diputar pada akhir untuk menghindari kesalahan paralaks. Skala ini dilengkapi dengan pengukuran yang berbeda dalam hal milimeter atau centimeter. KEUNTUNGAN PMMC : 1. Skala PMMC seragam dirancang. 2. Ini mengkonsumsi lebih sedikit daya ( 25μv untuk 200μv ) 3. Ini memiliki akurasi tinggi dalam pengukuran Dc. 4. Instrumen tunggal dapat digunakan untuk mengukur rentang yang berbeda dari arus dan tegangan dengan penambahan shunt dan seri resistor ke PMMC. Kekurangan OF PMMC : 1. Hal ini digunakan untuk pengukuran DC saja. 2. Hal ini lebih mahal dibandingkan dengan instrumen lainnya. Ketiga sistem diperlukan untuk mengoperasikan memuaskan, mereka 1. Membelokkan sistem torsi 2. Damping sistem torsi 3. Sistem Pengendalian torsi
Membelokkan SYSTEM : Kekuatan yang diterapkan pada pointer untuk membelokkan dari posisi nol disebut torsi membelokkan. Sistem ini instrumen mengubah energi listrik menjadi energi mekanik. PENGENDALIAN TORSI : Ketika gaya membelokkan diterapkan untuk penunjuk itu mengalihkan dan harus berhenti untuk nilai yang terukur. Dengan tidak adanya pengendalian torsi pointer tunas untuk nilai akhir untuk setiap besarnya saat ini. MEREDAM TORSI : pointer yang mengalihkan bila diterapkan dengan kekuatan membelokkan dan harus datang untuk beristirahat di posisi stabil. Pointer datang kembali ke posisi stabil ketika kekuatan membelokkan diimbangi oleh torsi mengendalikan. Dengan demikian berosilasi pointer dan sisanya pada posisi stabil, gaya ini dikenal sebagai gaya redaman.