printer series 3rd roll 3 Penggulung ketiga seri printer Assembly instructions 7 1 4 5 2 8 3 6 1. 3-inch right-hand adaptor 2. 2-inch right-hand adaptor 3. Intermediate support 4. 3-inch left-hand adaptor 5. USB dongle 6. Sliding support 7. Bail 8. Right-hand hub structure 1. 3 2. 2 3. 4. 3 5. USB 6. 7. 8. 1. 7.62cm 2. 5.08cm 3. 4. 7.62cm 5. USB 6. 7. 8. 1. 3 2. 2 3. 4. 3 5. USB 6. 7. 8. 1. 3 2. 2 3. 4. 3 5. USB 6. 7. 8. 1. Adaptor sisi kanan 3 2. Adaptor sisi kanan 2 3. Penyangga perantara 4. Adaptor sisi kiri 3 5. Dongle USB 6. Penyangga geser 7. Lengan 8. Struktur hub sisi kanan Please read these instructions carefully. These assembly instructions explain how to assemble the 3rd roll. Notice that the icon used in this document is also located on the packaging. The icon helps you locate the parts needed for the assembly. * Time required for assembly of the 3rd roll is approximately 15 minutes. **1 person is required to perform this task. 3 * 3 15 ** 1 * 15 ** * 15 ** 1 CHS CHT 1 Petunjuk Pemasangan * 15 ** 1 2010 Hewlett-Packard Company Large Format Division Camí de Can Graells 1-21 08174 Sant Cugat del Vallès Barcelona Spain All rights reserved Printed in XXX Baca petunjuk ini dengan cermat. Petunjuk pemasangan ini menjelaskan cara memasang penggulung ketiga. Perhatikan bahwa ikon yang digunakan dalam dokumen ini juga terdapat pada kemasan. Ikon membantu Anda menemukan komponen yang diperlukan untuk pemasangan. * Waktu yang diperlukan untuk pemasangan penggulung ketiga adalah sekitar 15 menit. ** Diperlukan 1 orang untuk menjalankan tugas ini.
Assemble the 3rd roll 3 Memasang penggulung ketiga 1 2 3 Insert the USB dongle into the USB slot located behind the printer. Follow the instructions that appear on the front panel. Put the 2-inch right-hand adaptor onto the right-hand hub structure. Slide the right-hand hub structure onto the extruding bar on the right-hand part of the printer. USB USB 2 USB USB 5.08cm 2 USB USB 2 USB USB 2 Masukkan Dongle USB ke slot USB di bagian belakang printer. Ikuti petunjuk yang muncul di Panel Depan. Pasang adaptor sisi kanan 2 pada struktur hub sisi kanan. Geser struktur hub sisi kanan pada batang yang menonjol di bagian sisi kanan printer.
4 5 6 7 Fix the right-hand hub structure with the screw provided with the 2-inch right-hand adaptor. Insert the sliding support into the holes of the bottom guide. Insert the top part of the sliding support into the slot. Press the stopper and slide the support out of the way, to the left. 2 5.08cm 3 2 2 Kencangkan struktur hub sisi kanan dengan adaptor sisi kanan 2 menggunakan sekrup yang disediakan. Pasang penyangga geser pada lubang pemandu bawah. Pasang bagian atas penyangga geser pada slot. Tekan penahan dan geser penyangga sepenuhnya ke sebelah kiri.
8 9 10 11 Insert the intermediate support into the top holes located in the printer slot. Push down the intermediate support until you hear it click. Take the bail and position it as circled above. Insert the bail into the right- and left-hand cover slots. 4 Pasang penyangga perantara pada lubang atas yang terletak di slot printer. Tekan ke bawah penyangga perantara hingga terdengar bunyi klik. Ambil lengan dan posisikan seperti gambar yang dilingkari di atas. Pasang lengan pada slot penutup di sisi kanan dan kiri.
12 13 14 Press the blue lever until you hear it click at both sides. Go to the front panel and press the OK key. The printer must restart. Remove the USB dongle from the printer. IMPORTANT: Do not throw away the dongle, it contains a license that you can uninstall on this, and install on any other supported printer. [OK] USB 5 OK USB OK USB OK USB Tekan tuas biru hingga terdengar bunyi klik di kedua sisi. Lihat Panel Depan, lalu tekan tombol OK. Printer akan menjalankan boot ulang. Lepas Dongle USB dari printer. PTING: Jangan buang dongle karena dongle memiliki lisensi yang dapat dihapus dari printer dan diinstal pada printer model lainnya yang didukung.
Changing to the 3-inch adaptor 3 7.62cm 3 3 Mengganti ukuran adaptor menjadi 3 1 2 3 Unscrew the 2-inch right-hand adaptor. Remove the 2-inch right-hand adaptor. Be sure to leave the right-hand hub structure in place. Slide the 3-inch right-hand adaptor onto the righthand hub structure. 2 2 3 5.08cm 5.08cm 7.62cm 6 2 2 3 2 2 3 Lepas sekrup dari adaptor sisi kanan 2. Lepas adaptor sisi kanan 2. Pastikan struktur hub sisi kanan tetap terpasang di tempat. Pasang adaptor sisi kanan 3 pada struktur hub sisi kanan.
4 5 6 Fix the right-hand adaptor onto the hub structure with the screw provided. Insert the 3-inch left-hand adaptor onto the sliding support. Fit the adaptor into the holes located on the sliding support and rotate it counter-clockwise until you hear it click. 3 7.62cm 7 3 3 Kencangkan adaptor sisi kanan 3 pada struktur hub sisi kanan dengan sekrup yang disediakan. Pasang adaptor sisi kiri 3 pada penyangga geser. Pasang adaptor pada lubang yang terletak di penyangga geser, lalu putar berlawanan arah jarum jam hingga terdengar bunyi klik.
Legal notices Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.