Proses Permesinan Logam

Transkripsi

1 Proses Permesinan Logam Proses Manufaktur II Sumber: Manufacturing Engineering & Technology Oleh: Serope Kalpakjian

2 Proses Permesinan Logam Proses permesinan logam juga dikenal dengan proses perautan, karena prinsip kerjanya adalah meraut/membuang bagian yg tidak diperlukan untuk mendapatkan bentuk akhir yg diinginkan 2

3 Proses Permesinan Logam Proses perautan logam ini dilakukan dengan memanfaatkan logam lain yang lebih keras, yang umumnya disebut pahat potong (cutting tools). Pahat potong ada yang bermata potong tunggal (single point tools) maupun bermata potong banyak (multi points tools). 3

4 Sub-bagian proses pemesinan Mesin perkakas Pahat (cutting tools) Fixture (pemegang benda kerja) Benda kerja. 4

5 Beberapa contoh fixtures 5

6 Cutting Tools Multi point tools Single point tools 6

7 Mengapa Proses Permesinan Diperlukan? Dimensional accuracy lebih mudah dicapai dp proses pembentukan yg lain (casting, extrusion, forging), Dapat melakukan proses finishing untuk mencapai geometri/ukuran yg diperlukan, Bisa mengerjakan fitur-fitur tertentu yg ada di benda kerja (sudut yg tajam, permukaan yg benar-benar datar (flatness)), Lebih ekonomis untuk jumlah komponen/part yg tidak terlalu banyak. 7

8 Kekurangan Proses Permesinan Energy yg diperlukan umumnya lebih besar dibandingkan dengan proses pembentukan lainnya. Material yang terbuang (waste materials) cukup banyak, Bila tidak dilakukan dengan baik, bisa berdampak buruk pada permukaan benda kerja maupun sifat material b kerja, Laju produksi rendah bila dibandingkan dengan proses lain (ekstrusi, rolling). 8

9 Berbagai Proses Permesinan & Mesin yang Digunakan Proses bubut (turning), mesin bubut (lathe), Proses milling, mesin milling (mesin frais), Proses drilling (pembuatan lubang), mesin drill press, Proses sekrap, mesin shaper & planer, Proses gerinda (grinding), mesin grinding, Proses permesinan non-konvensional (EDM, water jet machining, abrasive jet machining) 9

10 Mesin Bubut (lathe) 10

11 Mesin Bubut (lathe) Contoh-contoh Mesin bubut 11

12 Mesin Milling (mesin frais) Horizontal milling Vertical milling 12

13 Mesin Drill Press Large drilling machine Radial drilling machine Drill press 13

14 Mesin Shaper & Planer Mesin planer, digunakan untuk benda kerja dengan dimensi besar Mesin shaper 14

15 Mesin Gerinda (grinding) Mesin Gerinda NC precision grinding machine Surface grinding machine 15

16 Common Machining Operations Figure 21.1 Some examples of common machining operations. 16

17 Turning Operation (proses bubut silindris) Figure 21.2 Schematic illustration of the turning operation showing various features. 17

18 Turning Operation (proses bubut silindris) Contoh proses bubut silindris adalah pembuatan atau permesinan poros. Parameter prosesnya adalah: Kedalaman potong (doc), Pemakanan (feed), Kecepatan potong (cutting speed), Kecepatan pemakanan (feed rate). 18

19 Two-Dimensional Cutting Process Figure 21.3 Schematic illustration of a two-dimensional cutting process, also called orthogonal cutting: (a) Orthogonal cutting with a well-defined shear plane, also known as the Merchant Model. Note that the tool shape, depth of cut, t o, and the cutting speed, V, are all independent variables, (b) Orthogonal cutting without a well-defined shear plane. 19

20 Factors Influencing Machining Operations 20

21 Mechanics of Cutting Cutting ratio, r t t o c sin cos Shear angle preditions : Velocities, V c Vc r V V sin cos 21

22 Chip Formation by Shearing Figure 21.4 (a) Schematic illustration of the basic mechanism of chip formation by shearing. (b) Velocity diagram showing angular relationships among the three speeds in the cutting zone. 22

23 Cutting Forces Gaya potong perlu diketahui untuk menentukan/memilih mesin yang dayanya sesuai dengan gaya potong yg diperlukan. Menjamin agar proses pemotongan menghasilkan kualitas pemotongan yg baik, karena daya mesin yg tidak mencukupi menghasilkan hasil pemotongan yang jelek (permukaan kasar, dimensi tidak tepat, pahat cepat aus, proses potong lama). 23

24 Cutting Forces Figure (a) Forces acting on a cutting tool during two-dimensional cutting. Note that the resultant force, R, must be collinear to balance the forces. (b) Force circle to determine various forces acting in the cutting zone. 24

25 Cutting Forces and Power Shear force, F s F c cos F t sin Normal force, F n F c sin F t cos Total Power Coefficien t of friction, Total Power Power F c V F N Ft F c F F c t tan tan tan Power for shearing Power F s V s Power for friction Power FV c 25

26 Example 26

27 Range of Energy Requirements in Cutting Operations 27

28 Specific Energy (Specific Cutting Energy) Adalah besarnya energy yang diperlukan per volume chip yang dihasilkan, Merupakan energy yang dibutuhkan dalam proses pemesinan, Dalam proses pemesinan, volume chip yang dihasilkan/dibuang per satuan waktu; dinyatakan sebagai Material Removal Rate (MRR). MRR semakin besar, energy yang diperlukan untuk pemotongan akan semakin besar. 28

29 Chips Produced in Orthogonal Metal Cutting Figure 21.5 Basic types of chips produced in orthogonal metal cutting, their schematic representation, and photomicrographs of the cutting zone: (a) continuous chip with narrow, straight, and primary shear zone; (b) continuous chip with secondary shear zone at the chip-tool interface; (c) built-up edge; (d) segmented or non-homogeneous chip; and (e) discontinuous chip. Source: After M.C. Shaw, P.K. Wright, and S. Kalpakjian. 29

30 Built-up Edge (b) Figure 21.6 (a) Hardness distribution with a built-up edge in the cutting zone (material, 3115 steel). Note that some regions in the built-up edge are as much as three times harder than the bulk metal of the work-piece. (b) Surface finish produced in turning 5130 steel with a built-up edge. (c) Surface finish on 1018 steel in face milling. Magnifications: 15x. Source: Courtesy of Metcut Research Associates, Inc. (c) 30

31 Chip Breaker Figure 21.7 (a) Schematic illustration of the action of a chip breaker. Note that the chip breaker decreases the radius of curvature of the chip and eventually breaks it. (b) Chip breaker clamped on the rake face of a cutting tool. (c) Grooves in cutting tools acting as chip breakers. Most cutting tool used now are inserts with built-in chip breaker features. Chip breaker berfungsi untuk memotong continuous chip, agar chip tidak membelit pahat maupun benda kerja. 31

32 Chips Produced in Turning Figure 21.8 Chips produced in turning: (a) tightly curled chip; (b) chip hits workpiece and breaks; (c) continuous chip moving radially away from workpiece; and (d) chip hits tool shank and breaks off. Source: After G. Boothroyd. 32

33 Temperatures in Cutting Zone Mean temperature in cutting: 1.2Y T mean f c Vt o K where 1/3 Y f flow stress, psi c volumetric specific heat, in.- lb/in 3 - F K thermal diffusivity Figure Typical temperature distribution in the cutting zone. Note the severe temperature gradients within the tool and the chip, and that the workpiece is relatively cool. Source: After G. Vieregge. Mean temperature V a f b V : cutting speed, f : feed, a & b : konstanta. 33

34 Temperatures in Cutting Energy yang diperlukan untuk memisahkan chip dari benda kerja, dikonversi dalam bentuk panas sehingga menaikkan temperatur di daerah pemotongan (pahat chip benda kerja), Temperatur yang berlebihan memperpendek umur pahat, dimensi benda kerja tidak tepat, permukaan benda kerja yang kasar, Temperatur dalam pemotongan harus dijaga agar tidak terlalu tinggi (dengan menambah fluida pendingin, memilih parameter pemotongan yang tepat. 34

35 Temperatures Developed in Turning Steel Figure Temperatures developed in turning steel: (a) flank temperature distribution and (b) tool-ship interface temperature distribution. Source: After B. T. Chao and K. J. Trigger. 35

36 Temperatures Developed in Turning Steel Kurva di atas menunjukkan pengaruh cutting speed terhadap temperatur. Makin tinggi cutting speed, makin tinggi temperatur pemotongan. 36

37 Proportion of Heat from Cutting Transferred as a Function of Cutting Speed Energy panas yg dihasilkan selama proses pemotongan dipindahkan/dibuang melalui chip, benda kerja & pahat. Porsi energi panas terbesar dipindahkan melalui chip. Kurva di samping menunjukkan prosentase besarnya energi panas yang dipindahkan melalui chip, benda kerja & pahat. Figure Proportion of the heat generated in cutting transferred into the tool, work-piece, and chip as a function of the cutting speed. Note that the chip removes most of the heat. 37

38 Wear Patterns on Tools (Bentuk keausan pahat) Karena pahat bergesekan dengan benda kerja saat pemotongan berlangsung, pahat akan mengalami keausan (wear). Keausan timbul karena: (1) konsentrasi tegangan yang tinggi di lokasi tertentu, (2) temperatur pemotongan yang tinggi, (3) gesekan antara pahat dengan chip, (4) gesekan antara pahat dengan benda kerja yang sudah terpotong. 38

39 Types of Wear seen in Cutting Tools Figure (a) Schematic illustration of types of wear observed on various cutting tools. (b) Schematic illustrations of catastrophic tool failures. A wide range of parameters influence these wear and failure patterns. Source: Courtesy of V. C. Venkatesh. 39

40 Wear Patterns on Tools Figure (a) Flank wear and crater wear in a cutting tool; the tool moves to the left as in Fig (b) View of the rake face of a turning tool, showing various wear patterns. (c) View of the flank face of a turning tool, showing various wear patterns. (d) Types of wear on a turning tool: 1. flank wear; 2. crater wear; 3. chipped cutting edge; 4. thermal cracking on rake face; 5. built-up edge; 6. catastrophic failure. (See also Fig ) Source: Courtesy of Kennametal, Inc. 40

41 Taylor Tool Life Equation Taylor Equation: VT n C VT n d x f y C 41

42 Example 2 42

43 Effect of Work-piece Hardness and Microstructure on Tool Life Figure Effect of workpiece hardness and microstructure on tool life in turning ductile cast iron. Note the rapid decrease in tool life (approaching zero) as the cutting speed increases. Tool materials have been developed that resist high temperatures, such as carbides, ceramics, and cubic boron nitride, as will be described in Chapter

44 Tool-life Curves Figure Tool-life curves for a variety of cutting-tool materials. The negative inverse of the slope of these curves is the exponent n in the Taylor tool-life equation and C is the cutting speed at T = 1 min, ranging from about 200 to 10,000 ft./min in this figure. 44

45 Allowable Average Wear Land for Cutting Tools 45

46 Relationship between Crater-Wear Rate and Average Tool-Chip Interface Temperature Figure Relationship between crater-wear rate and average tool-chip interface temperature: 1) High-speed steel, 2) C-1 carbide, and 3) C-5 carbide (see Table 22.4). Note how rapidly crater-wear rate increases with an incremental increase in temperature. Source: After B. T Chao and K. J Trigger. 46

47 Cutting Tool Interface and Chip Figure Interface of a cutting tool (right) and chip (left) in machining plain-carbon steel. The discoloration of the tool indicates the presence of high temperatures. Compare this figure with the temperature profiles shown in Fig Source: Courtesy of P. K. Wright. 47

48 Machined Surfaces Produced on Steel (a) (b) Figure Machined surfaces produced on steel (highly magnified), as observed with a scanning electron microscope: (a) turned surface and (b) surface produced by shaping. Source: Courtesy of J. T. Black and S. Ramalingam. 48

49 Dull Tool in Orthogonal Machining Figure Schematic illustration of a dull tool with respect to the depth of cut in orthogonal machining (exaggerated). Note that the tool has a positive rake angle, but as the depth of cut decreases, the rake angle effectively can become negative. The tool then simply rides over the workpiece (without cutting) and burnishes its surface; this action raises the workpiece temperature and causes surface residual stresses. 49

50 Feed Marks on a Turned Surface Surface roughness: R a f 2 8R where f feed R tool - nose radius Figure Schematic illustration of feed marks on a surface being turned (exaggerated). 50

51 Cutting with an Oblique Tool Figure 21.9 (a) Schematic illustration of cutting with an oblique tool. Note the direction of chip movement. (b) Top view, showing the inclination angle, i,. (c) Types of chips produced with tools at increasing inclination angles. 51

52 Right-hand Cutting Tool and Insert Figure (a) Schematic illustration of right-hand cutting tool. The various angles on these tools and their effects on machining are described in Section Although these tools traditionally have been produced from solid tool-steel bars, they have been replaced largely with (b) inserts made of carbides and other materials of various shapes and sizes. 52