1. Buka Winbox lalu klik kotak dari Connect to. Lalu pilih IP Address atau MAC Address yang tertera di bawahnya, lalu masukan login username dan password, secara default username : admin, dan password : blank. Selanjutnya klik Connect 1. Open the Winbox, then click Connect to.then select IP Address or MAC Address is written in the bottom, and input username : admin, password : blank, and then click Connect 2. Masukkan IP Statik yang didapatkan dari Biznet dan dimasukkan di interface yang mengarah ke Wan (kabel Biznet), dalam hal ini : 117.102.85.138/29 (Subnet Mask : 255.255.255.248, gateway : 117.102.85.137). Berikut ini langkah-langkahnya : Klik IP > Addresses > Add (+) 2. Type the IP Static obtained from biznet and input to the interface that leads to Wan ( Biznet Wires ) in this case: 117.102.85.138/29 (Subnet Mask: 255.255.255.248, gateway: 117.102.85.137). Follow these steps: Click IP > Addresses > Add (+)
3. Klik IP > Routes > Add (+) > Destination (0.0.0.0/0), Gateway (contoh : 117.102.85.137), Pref. Source (contoh : 117.102.85.138). Hal ini dibutuhkan agar IP Statik yang didapatkan dapat di routing ke internet 3. Click IP > Routes > Add (+) > Destination (0.0.0.0/0), Gateway (example: 117.102.85.137), Pref.Source (example: 117.102.85.138).It is needed to make IP Static acquired can be in the routing to the internet
4. Untuk mengisi DNS, berikut langkahlangkahnya : IP > DNS > Settings > Primary DNS (203.142.82.222), Secondary DNS (203.142.84.222), setelah itu harap dicentang di bagian Allow Remote Requests 4. To fill the DNS following at the steps: IP > DNS > Setting > Primary DNS (203.142.82.222), Secondary DNS (203.142.84.222). After that, tick on Allow Remote Requests. 5. Setting NAT : Agar PC Client dapat terhubung ke internet maka perlu dilakukan Masquerade, berikut ini langkah-langkahnya : > IP > Firewall > NATt > Add (+) > Chain : srcnat > Out Interface : WAN > Action (tab) : Masquerade 5. NAT Setting : For connecting PC Client to the internet, it needs to be Masquerade, following the steps : > IP > Firewall > NAT > Add (+) > Chain : srcnat > Out Interface: WAN > Action (tab) : Masquerade
6. SETTING DHCP SERVER Klik IP Poo klik tanda (+) / add IP pool 6. SETTING DHCP SERVER Click IP Poo Click symbol (+) / add IP pool Nama IP pool secara default akan : hs-pool1 IP pool name will be in default : hs-pool1 Masukan range IP DHCP pada kolom Address dengan contoh format sbb 192.168.1.2-192.168.1.254 Insert range IP DHCP on column Address following example format: 192.168.1.2-192.168.1.254 Klik apply lalu OK Click apply, and then OK
7. Klik IP DHCP Server klik (+) / add DHCP server 7. Click IP DHCP Server Click (+) / add DHCP server Masukan DHCP name : bebas Insert DHCP name : any Masukan interface yg akan digunakan sebagai DHCP server Masukan address pool : sesuai dengan IP pool yang telah kita buat sebelumnya klik apply lalu OK Insert interface will be used for DHCP server Insert address pool : in accordance with IP pool we have made earlier Click apply, and then OK
8. Klik Tab Network klik (+) 8. Click Tab Network click (+) Masukan network address lengkap dengan subnetnya pada kolom Address, Contoh : 192.168.1.0/24 Masukan IP Gateway pada kolom Gateway Klik apply lalu OK Input complete network address with subnet in columns address, ex: 192.168.1.0/24 Insert IP Gateway in column Gateway Click apply, then OK
9. Untuk melakukan percobaan Ping dan Traceroute dapat dilakukan melalui program Telnet atau Tools > Ping dari Mikrotik 9. To doing test Ping and Traceroute can be done through the program Telnet or Tools > Ping of mikrotik