SHAFT ALIGNMENT. Definisi shaft alignment?

Ukuran: px

Mulai penontonan dengan halaman:

Download "SHAFT ALIGNMENT. Definisi shaft alignment?"

Teguh Dharmawijaya
7 tahun lalu
Tontonan:

1 ALIGNMENT POROS

2 SHAFT ALIGNMENT Definisi shaft alignment? Adjustment posisi relatif dari dua poros, ex. motor (driver & pompa (driven). Pengaturan posisi center pada kondisi operasi normal.

3 EFEK MISALIGNMENT ROTATING MACHINERY Distorsi poros (Shaft) Konsumsi energi meningkat Mengurangi umur bantalan Kerusakan seal Shut down tidak terjadwal.

4 Kondisi Aligned Misaligned seal terbuka kebocoran dan kontaminasi

5 JENIS MISALIGNMENT Parallel misalignment Angular misalignment

7 IDENTIFIKASI MISALIGNMENT Inspeksi peralatan Kerusakan awal pada bearing, seal, shaft, or coupling failures. Temperatur tinggi pada bearings atau minyak pelumass Kebocoran yang berlebihan pada seal Longgar baut pengikat kaki Longgar atau rusak baut pada kopling Pecah atau rusak karet pada fleksibel kopling

8 INSPEKSI PERALATAN Kerusakan tidak wajar pada kopling. Retaknya poros pada bagian bearing dekat kopling Penambahan pelumas yang berlebihan

9 DATA ANALISA VIBRATION Bentuk Vibrasi pada misalignment : Vibrasi pada arah aksial. High vibration at 1xTS or 2xTS in the spectrum. Signifikasi fase getaran 180 derajat

10 ANGULAR MISALIGNMENT Spectrum Phase High axial vibration both in 1X and 2X rpm 180 Out-of-phase across the coupling (axial axial).

11 PARALLEL MISALIGNMENT Spectrum Phase High radial vibration, 2x rpm often larger than 1x rpm, but its height relative to 1x rpm is often dictated by coupling type and construction 180 Out-of-phase across the coupling (horizontal horizontal or vertical vertical)

12 INFRARED THERMOGRAPH

13 FLEXIBLE COUPLING

14 FONDASI DAN BASEPLATE Bowed baseplate Skewed baseplate

15 PREALIGNMENT Sebelum melakukan alignment Kondisi fondasi. Kerusakan bearings, shafts, seals, couplings dll. Poros bengkok Softfoot

16 KOREKSI SOFT FOOT Soft foot = gap antara mesin dengan fondasi Diperbaiki sebelum alignment Soft foot menyebabkan tegangan pada baut dan bearing

17 KOREKSI SOFTFOOT Stress lines due to softfoot Pre-loading bearing due to softfoot

18 KOREKSI SOFTFOOT Bentuk umum softfoot

19 KORESKSI SOFT FOOT Dial Indicator Install a dial indicator on the foot and watching the movement as you loosen the hold down bolt. Laser Method Mount the laser on the machine shaft on either side of coupling Loosen individual bolt and retighten Read the live display

20 METODE ALIGNMENT Straight edge and feeler gauge Face & Rim Reverse Indicator

21 STRAIGHT EDGE

22 FEELER GAUGE

23 FACE & RIM PROSEDUR 1. Attached bracket firmly to one shaft and position indicators on face and periphery of other shaft Zero the indicators at the 12 o clock position Rotate slowly the shaft and bracket arrangement through 90 degrees interval stopping at the 3, 6 & 9 o clock positions. Record each reading (+ or -) Return to the 12 o clock position to see if the indicators rezero Repeat steps 2 through 4 to verify the first of readings

24 FACE & RIM

25 REVERSE INDICATOR PROSEDUR 1. Attached bracket(s) firmly to one shaft(s) and position indicator(s) on face and periphery of other shaft(s) Zero the indicator(s) at the 12 o clock position Rotate slowly the shaft and bracket arrangement through 90 degrees interval stopping at the 3, 6 & 9 o clock positions. Record each reading (+ or -) Return to the 12 o clock position to see if the indicator(s) re-zero Repeat steps 2 through 4 to verify the first of readings If one bracket was used, mount bracket on other shaft and repeat steps 1 through 5

26 REVERSE INDICATOR

27 DIAL INDICATOR MOUNTING Mounting buruk The stem does not perpendicular to the reading surface Mounting benar

28 DIAL INDIKATOR Dial tidak menyentuh

29 VALIDASI PEMBACAAN kiri + kanan = atas + bawah

30 PERPINDAHAN PERALATAN Vertical movement Horizontal movement Axial movement

31 CARA PEMBACAAN Apabila harga pergerakan dial dari arah jam 12 ke jam 6 Aktuak offset = ½ selish indikatir pada dial Axial view of the shaft

32 CARA MEMBACA Solusi matematis (+) = the unit has to be raised (add shim) for vertical movement or moved to the left for horizontal movement (-) = the unit has to be lowered or moved to the right

33 CARA PEMBACAAN Solusi matematis (+) = the unit has to be raised (add shim) for vertical movement or moved to the left for horizontal movement (-) = the unit has to be lowered or moved to the right

34 ALIGNMENT (Metode graphis)

35 ALIGNMENT (Metode graphis) Position of the driven shaft when the bottom reading is negative (-)

36 ALIGNMENT (Metode graphis) Position of the driven shaft when the bottom reading is positive (+)

37 ALIGNMENT (Metode graphis) Position of the driver shaft when the bottom reading is negative (-)

38 ALIGNMENT (Metode graphis) Position of the driver shaft when the bottom reading is positive (+)

39 LASER ALIGNMENT

40 LASER ALIGNMENT

41 LASER ALIGNMENT

42 LASER ALIGNMENT Keuntungan Cepat Panjang poros sampai 20 m Ketelitian tinggi Perhitungan otomatis Pengaruh temp. kecil Kekurangan Dikalibrasi secara periodik

43 TOLERANSI ALIGNMENT CSI Recommended Tolerances for Shaft Alignment Fixturlaser Recommended Tolerances for Shaft Alignment

44 LASER ALIGNMENT Ludeca Recommended Tolerances for Shaft Alignment John Piotrowski

dokumen-dokumen yang mirip

BAB II LANDASAN TEORI

BAB II LANDASAN TEORI 2.1 Pengertian Alignment Alignment adalah kesatu sumbuan, kesejajaran, kesebarisan dan ketegak lurusan elemen mesin pemindah putaran atau daya. Berikut komponen yang sering terjadi